- 您现在的位置：买卖IC网 > Sheet目录1197 > ATICE10 (Atmel)AVR IN CIRCUIT EMULATOR
AT90ADCPOD Configuration
Table 4-1. Jumper Settings when Selecting between ATtiny11, ATtiny12, ATtiny22,
AT90S2323 and AT90S2343
Device
PB3/J310
PB4/J311
Jumper Setting
AT90S2323, ATtiny11 or ATtiny12
OFF
OFF
OFF
PB4
ON
with External Crystal
OFF
PB3
ON
AT90S2343, ATtiny11, ATtiny12 or
OFF
ON
OFF
PB4
ON
ATtiny22 with External Clock
OFF
PB3
ON
AT90S2343, ATtiny11, Attiny12 or
ON
ON
OFF
PB4
ON
ATtiny22 with Internal Clock
Note:
OFF
The jumper setting does not affect operation for other devices.
PB3
ON
ATtiny11 and ATtiny12 also have the possibility to disconnect the external RESET pin
and use it as a general I/O pin (PB5). This is done by setting the jumper marked RST in
position OFF. Jumper RST must always be set in position ON for all other devices.
To use AT90S2333, AT90S4433, AT90S4434, or AT90S8535, the 10-lead cable on the
pod must be mounted. Table 4-2 shows how to connect this cable.
Table 4-2. Connections of 10-lead Cable
Device
AT90S2333 and AT90S4433
AT90S4434 and AT90S8535
10llead Cable
Connect ADC and ADC28
Connect ADC and ADC40
Note:
Connection of the 10-lead cable does not affect operation for other devices.
4.3
The ICE10 Power The ICE10 system has an internal power regulator that can deliver 15W at 5V. The
System
ICE10 itself uses about 10W, so if the user application is powered from the ICE10 sys-
tem, it cannot use more than 5W (i.e. 1A/5V). If this value is exceeded, the ICE10
system may be damaged or not work properly.
The power supply delivered with your ICE10 is dimensioned to meet the requirements of
the emulator. If another power supply is used, it should supply a voltage between 9 and
15 VDC, minimum 20W. The battery eliminator connector on the ICE10 system is a
standard type with 2.1 mm center tap. Center tap is negative.
4.3.1
The Target
Applications Power
Requirements
If the target application should be powered from the ICE10, the jumper named
“ EXT.POWER ” must be mounted and the jumpers labeled “ PW2 ” , “ PW1 ” and “ PW0 ”
removed.
If the target application has its own power supply, the jumper named “ EXT.POWER ”
must be removed. The ADCPOD must also be set to convert voltages to the required
voltage level. Use Table 4-3 to find the settings on the jumpers named “ PW2 ” , “ PW1 ”
and “ PW0 ” .
AVR ? ATICE10 User Guide
4-3
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ATICE50POD
REPLACEMENT POD FOR ICE40,ICE50
ATQT600IB
BOARD INTERFACE ATQT600IB
ATSTK1000
KIT STARTER FOR AVR32AP7000
ATSTK501
ADAPTER KIT FOR 64PIN AVR MCU
ATSTK502
MOD EXPANSION AVR STARTER 500
ATSTK503
STARTER KIT AVR EXP MODULE 100P
ATSTK504
STARTER KIT AVR EXP MOD 100P LCD
ATSTK505
ADAPTER KIT FOR 14PIN AVR MCU
相关代理商/技术参数
ATICE10UPGR
功能描述:KIT UPGRADE ICEPRO TO ICE10 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035
ATICE200
制造商:Atmel Corporation 功能描述:
ATICE200-
制造商:Atmel Corporation 功能描述:LOW COST ICE FOR AVR FAMILY
ATICE30
制造商:Atmel Corporation 功能描述:
ATICE40
功能描述:EMULATOR IN-CIRCUIT TINY26/MEGA8 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035
ATICE40UPGR
功能描述:KIT UPGRADE MEGA8515/8535 TINY13 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035
ATICE50
功能描述:仿真器/模拟器 AVR EMULATOR F/TINY AND MEGA DEVICES
RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
ATICE50/EVAL
制造商:Atmel Corporation 功能描述:DEV TOOL - Bulk